Jul 28,2020

Publication on subsidies for post-stabilization support in 2020

According to the “Notice of the People’s Government of Fujian Province on Fifteen Measures for Further Improving Employment and Entrepreneurship Work under New Conditions” (Minzheng [2015] No. 44), the “Notice on Further Improving Issues Related to Ensuring Job Stability through Unemployment Insurance Support for Enterprises” (Minrenshewen [2015] No. 291), the “Notice on Further Enhancing Work Related to Ensuring Job Stability and Upskilling under Unemployment Insurance Support for Enterprises” (Minrenshewen [2019] No. 130), and the “Notice of the Department of Human Resources and Social Security of Fujian Province, the Department of Industry and Information Technology of Fujian Province, the Department of Education of Fujian Province, the Department of Finance of Fujian Province, the Department of Transport of Fujian Province, and the Commission of Health and Family Planning of Fujian Province on Supporting Enterprises in Resuming Operations and Retaining Jobs during the Epidemic Prevention and Control Period” (MRSHW [2020] No. 23).

Nov 22,2019

Publicity of the 2019 post-stabilization subsidy

In accordance with the spirit of the “Notice of the Fujian Provincial People’s Government on Fifteen Measures for Further Improving Employment and Entrepreneurship Work under New Conditions” (Min Zheng [2015] No. 44) and the “Notice on Further Improving Issues Related to Employment Stabilization Work under the Support of Unemployment Insurance for Enterprises” (Min Ren She Wen [2015] No. 291), our company has submitted an application to the Fuan City Employment Management Center for an employment stabilization subsidy for 2019, totaling 9,520 yuan. The funds from the employment stabilization subsidy will be used for the following purposes: payment of living allowances to employees, payment of social insurance contributions, training for job transfers, skills enhancement, and other related expenses.

Aug 05,2019

Ten years of thermal pump development! Fujian Huada Electric Co., Ltd. has once again earned the prestigious title of “Outstanding Component Supplier in the Thermal Pump Industry 2019”!

On August 1, the 2019 Annual Conference of China’s Heat Pump Industry and the 8th International Forum on the Development of Air Source Heat Pump Industry were held with great fanfare at the Holiday Inn Shanghai Greenland Hotel. The event was organized by the China Energy Conservation Association and hosted by the Special Committee on Heat Pumps of the China Energy Conservation Association and the China Heat Pump Industry Alliance.

Jun 21,2019

Cool and refreshing on the summer solstice—Huada’s electrical equipment exhibition in June

The stars are heavy, the day is hot, and the dew feels the fragrance of the lotus. On the summer solstice, when the sky is overcast with clouds, cicadas sense the gloomy weather and sing from the branches of lilac trees. The summer solstice has arrived—how can I feel the gentle breeze that’s about to blow? Fujian Huada Fun Machinery Co., Ltd. will be participating in the exhibition in June to bring you a breath of cool air.

Feb 14,2019

Great luck at graduation | 2019 Set off on your journey and achieve new success!

Great luck to start with! | 2019 Set off on your journey and achieve new success!

May 16,2018

Precautions when servicing the circulation fan

Proper maintenance is a crucial guarantee for the safe and reliable operation of a circulating fan, and it also helps extend its service life. Therefore, when using circulating fans for tobacco processing, it is essential to pay adequate attention to them. At the initial stage of impeller operation and during all routine inspections, whenever possible, the impeller should be examined for defects such as cracks, wear, and dust accumulation. Whenever feasible, the impeller must be kept clean and regularly brushed with a wire brush to remove dust and rust deposits. Over time, this accumulated dust may settle unevenly on the impeller, disrupting its balance and causing rotor vibrations. After repairing the impeller, it must be dynamically rebalanced. If conditions permit, a portable balancing device can be used to perform balancing directly on-site. Before conducting dynamic balancing, it is necessary to check that all fastening bolts are properly tightened. "Since the impeller has been operating in an unbalanced condition for some time, these bolts might have become loose." Apart from regular inspections of the internal housing and suction chamber for severe wear and removal of heavy dust deposits, no additional special repairs are required for these components. Regularly verify that all fastening bolts are securely tightened. In fans equipped with compression bolt assemblies, press the butterfly spring on the support until it reaches the installation level indicated in the drawing. During bearing unit maintenance, the supply of lubricating oil to the bearings is often checked. If oil leakage is observed in the housing, slightly tighten the bolts on the end cover. If this does not suffice, it may be necessary to replace the sealing gasket with a new one. Maintenance of other auxiliary equipment, including motors, electric drives, instruments, and measuring devices, is described in detail in their respective operating manuals. These manuals are provided by various manufacturers of auxiliary equipment, and our manufacturer will deliver these manuals to users in random packaging. Repair and maintenance of high-temperature circulating fans when they are out of service: When the fan is not in use and the ambient temperature drops below 5 ℃, any residual water in the equipment and piping should be drained to prevent damage to the equipment and piping due to freezing. Maintenance of tobacco-processing circulating fans operated by smoke drying during prolonged shutdowns and storage: Cover the surfaces of bearings and other critical components with an anti-corrosion oil to prevent corrosion. The rotor of a high-temperature circulating fan used for tobacco processing should be manually rotated by half a turn (that is, by 180°) approximately every two weeks. Before rotating the rotor, the end of the shaft should be marked so that the original top point becomes the bottom point after the rotor is moved.